Tab Content
  • SLP's Avatar
    1 Hour Ago
    SLP replied to a thread Transmission 2nd gear issue in Gen V
    Usually will cover it in my experience. Might tell you to come back when it's worse. Just don't tell them if you've ever taken the car on a track,...
    4 replies | 118 view(s)
  • SLP's Avatar
    3 Days Ago
    SLP replied to a thread Weld in cage in Gen V
    That's good news. I'm going to attempt a self-completed targa conversion this winter. Fingers crossed.
    18 replies | 321 view(s)
  • SLP's Avatar
    4 Days Ago
    SLP replied to a thread 2013 Gen V Spun Bearing in Gen V
    Track "racing" Don't do that or speak of it if you want your warranty.
    236 replies | 6283 view(s)
  • SLP's Avatar
    4 Days Ago
    SLP replied to a thread 2013 Gen V Spun Bearing in Gen V
    Be very careful not to do/say anything that would void the warranty else wise. That's where I went wrong. Once the threat of litigation came up, they...
    236 replies | 6283 view(s)
  • SLP's Avatar
    5 Days Ago
    Goal: Removing the driver's side cylinder head with head studs and front timing cover in place. Situation: I am using ARP head studs instead of...
    0 replies | 80 view(s)
  • SLP's Avatar
    6 Days Ago
    SLP replied to a thread Alignment in Gen V
    I just started doing research on this and here are some of the directions alignments can go from what I can tell so far: 1) Standard alignment to...
    15 replies | 363 view(s)
  • SLP's Avatar
    1 Week Ago
    SLP replied to a thread 2013 Gen V Spun Bearing in Gen V
    Obligatory dodge warranty/service system sucks. Good luck OP. 4x transmission replacements because they didn't realize the TOB was bad. Tied my car...
    236 replies | 6283 view(s)
  • SLP's Avatar
    1 Week Ago
    SLP replied to a thread Potential buy in Gen V
    Probably calvo motor mounts and calvo upper coolant pipe. Good upgrades. Nothing to be concerned about.
    17 replies | 549 view(s)
  • SLP's Avatar
    2 Weeks Ago
    SLP replied to a thread Need some track upgrades in Gen V
    Radiator: Ron Davis Radiator & Calvo or RSI rigid upper coolant pipe. Intake: k&n drop in filter & Doug Shelby Engineering intake heat shield ...
    54 replies | 1020 view(s)
  • SLP's Avatar
    2 Weeks Ago
    Just got back in town for the weekend and am hopefully finishing up all the loose ends. Today this happened: 1) Removed TKO transmission mount and...
    142 replies | 9206 view(s)
  • SLP's Avatar
    2 Weeks Ago
    SLP replied to a thread Best Full Exhaust in Gen V
    This is my first car with an aggressive cam...I have a hard time turning off my car. I absolutely agree hah I used 2x Vibrant 1795 resonators on...
    30 replies | 839 view(s)
  • SLP's Avatar
    2 Weeks Ago
    SLP replied to a thread Best Full Exhaust in Gen V
    0:51 onward the cam catches a nice rhythm. https://www.youtube.com/watch?v=gOUy9jg6k8Q
    30 replies | 839 view(s)
  • SLP's Avatar
    2 Weeks Ago
    Me as well, I guess I'm late to know about the situation. If someone went after my company based on a premise like that, I would be livid.
    264 replies | 12250 view(s)
  • SLP's Avatar
    2 Weeks Ago
    SLP replied to a thread Best Full Exhaust in Gen V
    If I could do it all over again, I would fab my own inconel equal length headers. If I had a lot of money to spend, I would go with BBG headers. I...
    30 replies | 839 view(s)
  • SLP's Avatar
    2 Weeks Ago
    SLP replied to a thread 2013 Gen V Spun Bearing in Gen V
    I would recommend using these sort of occurances as a reason to build your engine up and ditch the warranty. I kept having to go at bat with...
    236 replies | 6283 view(s)
  • SLP's Avatar
    3 Weeks Ago
    Try navigating to the onboard code reader on the dash screen above the steering wheel (stethoscope icon) if you don't have a scanner on hand. It will...
    12 replies | 268 view(s)
  • SLP's Avatar
    3 Weeks Ago
    What code did it throw? That's important info to provide when asking people for help, especially when asking what caused the code. Could be as simple...
    12 replies | 268 view(s)
  • SLP's Avatar
    3 Weeks Ago
    SLP replied to a thread Not Starting first try in Gen V
    Probably a non-issue. Update us if it's a reoccurring problem.
    43 replies | 788 view(s)
  • SLP's Avatar
    3 Weeks Ago
    SLP replied to a thread Not Starting first try in Gen V
    I think that happened to my viper when it was stock once or twice after sitting for a while. Never persisted past that. Did you throw any error...
    43 replies | 788 view(s)
  • SLP's Avatar
    3 Weeks Ago
    Covers don't scratch the car by themselves. It's particulates trapped inbetween. All car covers usually create fine scratches unless you wash your...
    10 replies | 293 view(s)
  • SLP's Avatar
    3 Weeks Ago
    Targa Top...like prefix used to offer. There's a good amount of interest in this among gen V owners. Targa Top seals and latch kit. I'll...
    67 replies | 1818 view(s)
No More Results

2 Visitor Messages

  1. Pictures would be great, thank you! I am very interested.

    I have a GTS with sidewinder II wheels.
  2. View Conversation
    Erikkson,

    Did you plan to install them on a GTS or TA? Not sure if you're aware the TA Brembo rotors have a wider radial depth than the SRT or GTS factory setup, which offers greater thermal capacity at the cost of additional weight. This set of AP-Racing j-hooks are a direct bolt to the GTS or SRT brakes, however can be used for the TA using a different pad size.

    $1700 +shipping for the rotors and pads would work for me. I can collect some photos this weekend if interested.
Showing Visitor Messages 1 to 2 of 2
About SLP

Basic Information

Date of Birth
September 15, 1992 (27)
About SLP
Location:
Oregon

Signature


2013 GTS - Self Installed Heads/Valvetrain/Cam/Custom Exhaust. Triple carbon clutch and built tr6060.

Statistics


Total Posts
Total Posts
172
Posts Per Day
0.21
Visitor Messages
Total Messages
2
Most Recent Message
10-04-2019
General Information
Last Activity
1 Hour Ago
Join Date
03-03-2018