Search:

Type: Posts; User: TheMadMachinist

Page 1 of 20 1 2 3 4

Search: Search took 0.45 seconds.

  1. Yes. I think I will be cutting an inch off the...

    Yes. I think I will be cutting an inch off the bottom the full length on all of them. My car has lowering caps and I am dragging these things everywhere.
  2. 49901[/ATTACH [ATTACH=CONFIG]49900 Here's a...

    49901[/ATTACH [ATTACH=CONFIG]49900 Here's a couple pictures my car has lowering caps.
  3. Replies
    13
    Views
    330

    Who was it on here that was doing black Gen 5 gas...

    Who was it on here that was doing black Gen 5 gas caps if you sent yours in for a core?
  4. Replies
    12
    Views
    712

    TKO is making a wide body Gen 5 race car. All...

    TKO is making a wide body Gen 5 race car. All carbon fiber if I remember correctly. I stopped in and visited with Marty a couple months back and he gave up a tour of the shop. A what a cool guy and a...
  5. Replies
    17
    Views
    734

    How about a pair of blue stripes?

    How about a pair of blue stripes?
  6. What dave6666 said Stainless Steel bolts are much...

    What dave6666 said Stainless Steel bolts are much softer than you mite think and way softer than Grade 5.
  7. Replies
    9
    Views
    233

    Then this would be true of the Gen 5"s as well?

    Then this would be true of the Gen 5"s as well?
  8. Replies
    13
    Views
    285

    Just unplug it and see if the car starts and if I...

    Just unplug it and see if the car starts and if I doesn't then you must have pull it out when rearranging wires.
  9. I have to agree with Arizona Vipers. I do...

    I have to agree with Arizona Vipers.

    I do feel little sorry for all the collectors out there. Only because as enjoyable as it must be to look at one of these cars sitting in your collection. That...
  10. As far as the dried out bushings. The car was...

    As far as the dried out bushings. The car was making or I should say the suspension was making some pretty bad noise and there was defiantly slop in the bushings as I could feel it though the...
  11. I believe I have this same issue on my 2013 with...

    I believe I have this same issue on my 2013 with 59,000 miles. I just had all four lower control arms replaced under extended warranty due to the bushings being dry out. At that time the Tech did...
  12. Replies
    10
    Views
    525

    It looks very pissed off.

    It looks very pissed off.
  13. Replies
    21
    Views
    598

    I believe all you have to do is file out a little...

    I believe all you have to do is file out a little bit on on one spot on the inside of the wheel and your good to go.
  14. Replies
    21
    Views
    598

    I added a Gen 5 wheel and had the dash and...

    I added a Gen 5 wheel and had the dash and console painted to match the door pulls. I would have to say the Gen 5 Steering wheel is with out the best mod i have done to this car.49211
  15. Replies
    15
    Views
    650

    After reading Steve's post I couldn't help but...

    After reading Steve's post I couldn't help but think of one of my favorite things about these cars. That would be:

    One must aways remember to open and hold the door. Anytime a Lady mite be getting...
  16. Replies
    11
    Views
    498

    Dan maybe you could try something like "Viper...

    Dan maybe you could try something like "Viper advise by the minute" kind of like those phone sex deals. Then you could charge a fixed rate per minute. Your time is money, right?
  17. So when will they be ready?

    So when will they be ready?
  18. Replies
    19
    Views
    994

    As far as Gen 2 cars are concerned if you have...

    As far as Gen 2 cars are concerned if you have your heart set on a Paxton setup. Be aware that the weak point is the crank snout. I sure I am not the only one to snap one in two. I do believe it's...
  19. Replies
    19
    Views
    994

    That would depend on where you are located. ...

    That would depend on where you are located.

    Always best to fix the nut behind the wheel first.lol
  20. phantomapollyon, I can't help you with any...

    phantomapollyon, I can't help you with any measurements. Just an excuse to post a picture of my own.49039
  21. Replies
    19
    Views
    994

    How about some track lessons.

    How about some track lessons.
  22. I stopped in at his shop about a week ago and he...

    I stopped in at his shop about a week ago and he told me that rear diffuser kits are about four weeks out and to watch this thread for any up dates.
  23. Replies
    38
    Views
    1,119

    GTS Dean, Point well taken. Any and all...

    GTS Dean, Point well taken.

    Any and all suspension geometry measurements must be taken from the frame . The point I was trying to make is that the body is just kind of bolted on after the fact....
  24. Replies
    7
    Views
    571

    Sounds like a conspiracy to me.lol

    Sounds like a conspiracy to me.lol
  25. Replies
    38
    Views
    1,119

    That's interesting I have .430 wide spacers on...

    That's interesting I have .430 wide spacers on the front of mine. Never rubbed once.

    It kind of makes me wonder what they use for tolerances at the factory.lol
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4