Search:

Type: Posts; User: Redx

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Jesels look great, i believe they require...

    Jesels look great, i believe they require machining and valve cover spacers, not exactly a bolt on affair. Im doing the higher rpm 9l Tune so need some extra insurance as well.

    I see T&D offer a...
  2. Im sure scot can chime in on this, but there has...

    Im sure scot can chime in on this, but there has been a low failure rate on them(3 total and only on 9l cars) and only had failed on exhaust side. Prefix offers the bushing kit installed in the...
  3. Thread: nth Moto Clutch

    by Redx
    Replies
    17
    Views
    589

    Another +1 for this unit, I’ve had stock, McLeod...

    Another +1 for this unit, I’ve had stock, McLeod then the nth. The McLeod was fairly rough for daily use but found I could slip it pretty good at the track. The nth is buttery smooth for daily...
  4. Thread: Instagram

    by Redx
    Replies
    27
    Views
    1,805

    @rredx

    @rredx
  5. Not so much a gen 5 problem(more a g3-g4) but...

    Not so much a gen 5 problem(more a g3-g4) but might be worth checking engine mounts. Whenever i tore or had a cracked mount the engine flex would prevent it from going into gear or very difficultly.
  6. Thread: Sound Thread

    by Redx
    Replies
    29
    Views
    1,321

    https://youtu.be/4jmVIP5Rg8g

    https://youtu.be/4jmVIP5Rg8g
  7. Thread: Sound Thread

    by Redx
    Replies
    29
    Views
    1,321

    https://youtu.be/e6PlucJwCxo Prefix 9l xtreme...

    https://youtu.be/e6PlucJwCxo

    Prefix 9l xtreme arh 1 3/4, belanger catless exhaust.
  8. Thread: New 9LE Build

    by Redx
    Replies
    22
    Views
    1,022

    It doesn’t get overly hotter per say over a reg...

    It doesn’t get overly hotter per say over a reg 8.4, but heat soak mitigation can be done with heat wrapping and the dse shield.
  9. Replies
    9
    Views
    500

    I have since removed the carbon covers and ran...

    I have since removed the carbon covers and ran without them for the summers only modifying for the oil cap so far. I have a Cf hood I’ll modify instead of completely gouging up my Gen 4 hood.
    ...
  10. Thread: New 9LE Build

    by Redx
    Replies
    22
    Views
    1,022

    Definitely do the header wrap, these 9Ls get hot!...

    Definitely do the header wrap, these 9Ls get hot! Would look into getting the DSE intake heat shield, then have prefix modify it for the accusump. Also prefix was testing solid rockers last time my...
  11. Replies
    9
    Views
    500

    10.5@138, terrible 1.8 60'. DA was around 3800....

    10.5@138, terrible 1.8 60'. DA was around 3800. Definitely has a low 10 in it, track prep was non existent and was just spinning like a bastard. Ill try again next year at a private track day when...
  12. Replies
    9
    Views
    500

    It’s a pure street car, have done a few 1/4 mile...

    It’s a pure street car, have done a few 1/4 mile track runs but other than that just street pulls. It’s a prefix 9L xtreme, dyno’d 718whp on a green motor. Very street able .
  13. Replies
    9
    Views
    500

    You will need the full gen 5 valve covers(below...

    You will need the full gen 5 valve covers(below the beauty covers). I had my entire top end(heads, IM, pcv, valve covers and carbon fibre beauty covers) switched to gen 5 when prefix built my engine....
  14. Replies
    155
    Views
    8,050

    It would need some type of a2w airbox, not a lot...

    It would need some type of a2w airbox, not a lot of room there for one.
  15. Replies
    77
    Views
    2,671

    If its prefix tuned you can completely remove the...

    If its prefix tuned you can completely remove the o2's as they arent used anyways for the h/c and 9L builds and tuck the the wiring up and out of the way.
  16. Replies
    10
    Views
    884

    Negative. Removed Top and bottom of the mount the...

    Negative. Removed Top and bottom of the mount the rubber mount is all. There’s enough room in the top to get a flex head ratchet wrench in there to loosen and tighten.
  17. Replies
    10
    Views
    884

    Steve I’ve changed mine 4 times now lol. They are...

    Steve I’ve changed mine 4 times now lol. They are much easier with aftermarket headers in place. I left headers attached, removed the front bar, and unhooked the exhaust at the turnouts. I only...
  18. Replies
    11
    Views
    636

    Do you have a picture Steve911? Very interested...

    Do you have a picture Steve911? Very interested to see the Gen 3 product.
  19. Replies
    137
    Views
    20,661

    Came with the wheel, I have no clue where they...

    Came with the wheel, I have no clue where they were sourced but looks oem!

    38931
  20. Replies
    13
    Views
    496

    On a weekend unlikely, plus it will take a few...

    On a weekend unlikely, plus it will take a few days once you find a place. Go to ct and buy one of the “slime” kit which fills full of that foam crap, it sucks since it makes a mess for the tire...
  21. Replies
    21
    Views
    851

    whats the difference with this new cam?

    whats the difference with this new cam?
  22. Replies
    14
    Views
    607

    I’m waiting on another set of tires for my bbs,...

    I’m waiting on another set of tires for my bbs, but when they show up I have a minty set of hyper black sw2’s with near new toyo r888’s I’ll be selling in a few weeks.
  23. Replies
    17
    Views
    1,217

    so does the gen 3/4 use r hooks or j hooks?...

    so does the gen 3/4 use r hooks or j hooks? seeing people here use both, but would like the best fit.
  24. See attached. Thanks @chris topher(his forum id...

    See attached. Thanks @chris topher(his forum id eludes me at the moment) for figuring this out. 37067
  25. I believe he used for a mid 2000’s Mazda, you...

    I believe he used for a mid 2000’s Mazda, you just need one with a can hi/can lo input and tap into your obd2 plug.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4