Search:

Type: Posts; User: Steve M

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: Drying Towel

    by Steve M
    Replies
    46
    Views
    2,505

    *if you use both motors. If you only have a...

    *if you use both motors.

    If you only have a 15-amp outlet, you can still run 1 of the 2 motors, but it is a bit anemic. I've used it that way in the past...it does get the job done, just a bit...
  2. Replies
    10
    Views
    369

    I had not considered that. I don't think the Gen...

    I had not considered that. I don't think the Gen 4/5 Viper MAP sensor has dual-functionality though.

    The Gen 4/5 MAP sensor has 3 wires with the following pin-outs:
    ...
  3. Replies
    21
    Views
    402

    A couple more thoughts on the transmission fluid...

    A couple more thoughts on the transmission fluid while I'm thinking about it...

    ---------------------------------------------------------------------------------------------
    Why you might want to...
  4. Replies
    21
    Views
    402

    Depends on how you use your vehicle. If you...

    Depends on how you use your vehicle.

    If you race it hard, I'd change the transmission and differential fluids after every track weekend. If you are a bit easier on your car at the track, you might...
  5. Replies
    10
    Views
    369

    It isn't exactly clear...someone like Winkles...

    It isn't exactly clear...someone like Winkles would know. It could just be an HPTuners thing (although I doubt it), but even without an MAT sensor, it could still be calculated based on some...
  6. Thread: Gen IV Codes

    by Steve M
    Replies
    3
    Views
    140

    Excellent...glad you were able to get it sorted!...

    Excellent...glad you were able to get it sorted!

    And thanks for the insights...mine has been okay, but I did end up having to replace my camshaft position sensor last year. Tips on replacing that...
  7. Replies
    10
    Views
    369

    It does not...the only sensor on the intake...

    It does not...the only sensor on the intake manifold is the absolute pressure sensor that plugs in the passenger side toward the back of the manifold by the cowl.

    The PCM does reference MAT in...
  8. Replies
    5
    Views
    123

    Also, for what it's worth (pretty much nothing),...

    Also, for what it's worth (pretty much nothing), it is something you can alter with aftermarket tuning software:

    https://i.ibb.co/9Zp5X2p/Viper-AC-Disengage.png
  9. Replies
    5
    Views
    123

    This thread has some info:...

    This thread has some info: https://driveviper.com/forums/threads/14581-AC-performance
  10. Replies
    10
    Views
    369

    Gen 4s and 5s pull a pretty significant amount of...

    Gen 4s and 5s pull a pretty significant amount of timing when the inlet temps go over 77°F.

    If it is 85°F ambient, you can bet your IATs are +15-20° over that mark.

    Under those conditions, I...
  11. Replies
    5
    Views
    123

    AC should disengage during heavy acceleration,...

    AC should disengage during heavy acceleration, likely a function of how far you push down the loud pedal. If it didn't, the compressor might not like it very much.

    My amateur opinion: totally...
  12. Replies
    12
    Views
    420

    cashcorn? ...

    cashcorn?

    https://driveviper.com/forums/threads/28296-White-2016-ACR-on-Bring-a-Trailer?p=436766&viewfull=1#post436766
  13. A well driven stock Gen 5 should trap well into...

    A well driven stock Gen 5 should trap well into the upper 120s in the quarter mile. Tony (NineBall) drove one stock Gen 5 to a 134 trap speed (no e.t. given), but I'd consider that an outlier.
    ...
  14. Rubbing in the front, rear, or both? From what...

    Rubbing in the front, rear, or both?

    From what I remember, the fronts sit out further, but the rears should be about the same.

    Rear fender liner rubbing is a known issue when lowering a Gen 3/4...
  15. Replies
    9
    Views
    127

    Whatever you end up doing, the shock valving...

    Whatever you end up doing, the shock valving needs to be able to handle the spring rate chosen. If you go with too heavy of a spring, the shock won't be able to control it, and the ride will suffer...
  16. Pretty sure the Gen 3 valve covers are cast...

    Pretty sure the Gen 3 valve covers are cast aluminum. Assuming that's the case, you can sand/sand blast/chemically remove the paint, and also polish the letters. They'll take paint/powder, provided...
  17. Might want to read through this thread:...

    Might want to read through this thread: https://driveviper.com/forums/threads/26973-New-TPMS
  18. That's going to depend on what each state is...

    That's going to depend on what each state is looking for, and what they'll allow.

    The big issue is the readiness tests - things like the O2 sensors will not show as "ready" with the Prefix PCM.
    ...
  19. The Gen 3/4 TPMS system is a very simple one. ...

    The Gen 3/4 TPMS system is a very simple one.

    TPMS Light = low tire pressure, but it doesn't tell you which one(s), or what the pressures are.

    The information is reported by each of the...
  20. Replies
    3
    Views
    177

    I looked into this years ago...I'm no expert, but...

    I looked into this years ago...I'm no expert, but I'll share what I found. Hopefully it helps.

    One of the major issues with a new differential is how tight it is, but it's by design. New bearings...
  21. Thread: Gas Shortage

    by Steve M
    Replies
    14
    Views
    662

    There's currently a gas shortage in my Viper's...

    There's currently a gas shortage in my Viper's tank...need to fix that ASAP.
  22. For the OP, this is what he's talking about...

    For the OP, this is what he's talking about doing: https://driveviper.com/forums/threads/26284-Door-Hinge-Maintenance

    The procedure should be similar for the Gen 5.
  23. The only substantial difference with the Gen 4/5...

    The only substantial difference with the Gen 4/5 is the differential itself. It is apparently stronger than the Gen 3 design, but I can assure you, wheel hop is definitely still a problem depending...
  24. Prefix has access to the source code, so they can...

    Prefix has access to the source code, so they can do pretty much anything you'd ever want to do.

    Several folks have had Dick Winkles (he's THE guy) do custom tunes - how much that costs? No clue,...
  25. It can be, if you (or someone you pay) are...

    It can be, if you (or someone you pay) are willing to take the time to optimize it. A high volume shop is likely going to give you a "canned" HPTuners file that they've developed that will get you...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4