Search:

Type: Posts; User: Steve M

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. The '04 doesn't look hateful, but "excellent...

    The '04 doesn't look hateful, but "excellent condition" is a bit of a stretch IMO based on the couple pics provided. At the very least, it is missing the top piece of the stock intake/air box...
  2. Let me get that for ya: ...

    Let me get that for ya:


    https://youtu.be/l28Byi0fyNM

    Bad ass car for sure.
  3. Replies
    32
    Views
    768

    Poll: Sweet Corvette.

    Sweet Corvette.
  4. Replies
    26
    Views
    683

    For most cars, that wouldn't be a problem since...

    For most cars, that wouldn't be a problem since the aftermarket parts suppliers would normally step in and keep cranking stuff out. That's a tough sell for a low production number vehicle that uses...
  5. Replies
    26
    Views
    683

    Well, one thing is for sure - if you think it is...

    Well, one thing is for sure - if you think it is bad now, it's only going to get worse from here. A warranty is only as good as the service department that does the work, and for most of us, we...
  6. Replies
    11
    Views
    232

    Agreed...I used it to pick up a tach signal for...

    Agreed...I used it to pick up a tach signal for my shift light. I just clamped it around one of my coil wires, and off I went. But that's on a Gen 4, which has a coil-near-plug ignition setup (one...
  7. Replies
    30
    Views
    40,095

    If you have everything lined up (you know what...

    If you have everything lined up (you know what you are doing for PCV routing, have Doug Shelby's adapters, etc.), it should go pretty quick. I had mine done in a few hours, and I work SLOW.
  8. Replies
    6
    Views
    136

    If you have access to a code reader/scanner,...

    If you have access to a code reader/scanner, clear the DTCs and see if it comes back. It could be one of those that take a couple of cycles to clear. If everything is plugged in and functioning...
  9. Replies
    21
    Views
    534

    Agreed on the first part...cycling the defroster...

    Agreed on the first part...cycling the defroster should have been a part of every pre-delivery inspection before a Viper left the showroom floor, especially once they realized it was a problem (which...
  10. Thread: Clutch Squeak

    by Steve M
    Replies
    6
    Views
    380

    If you ever have to replace your clutch, add a...

    If you ever have to replace your clutch, add a remote bleeder while you are in there:

    https://driveviper.com/forums/threads/23197-How-to-Make-Your-Own-Clutch-Bleeder-Line

    The only issue is that...
  11. Replies
    136
    Views
    4,511

    I feel like it is less about the cost, and more...

    I feel like it is less about the cost, and more about the value.
  12. Heh...thanks. Spent longer on that than I care...

    Heh...thanks. Spent longer on that than I care to admit (both the project and the writeup).



    Well, chances are that if you already broke the nylon bushing, you'll probably break it again. ...
  13. Are you guys absolutely sure your nylon bushing...

    Are you guys absolutely sure your nylon bushing is broken? I only ask because I went with a bronze bushing on my old Camaro with a T-56, and it greatly increased NVH in the cabin. Yeah, the bronze...
  14. Replies
    136
    Views
    4,511

    That might be worth considering, but in my mind,...

    That might be worth considering, but in my mind, if I'm contributing to the forum by answering questions and posting how-to's (i.e. giving my time for free), why would I want to pay for that? I...
  15. Replies
    136
    Views
    4,511

    This is me right here. Too much drama, too much...

    This is me right here. Too much drama, too much politics. Anytime people refer to a car club as a business, it makes my hair stand on end. I was once a paid member of the VCA, but when that whole...
  16. Replies
    1
    Views
    160

    This info pinned at the top of this section will...

    This info pinned at the top of this section will get you close:

    https://driveviper.com/forums/threads/1608-Gen-3-amp-4-Production-Numbers

    Canadian cars might be harder to figure out, but not...
  17. Replies
    50
    Views
    1,991

    If you are serious, send him an email...he...

    If you are serious, send him an email...he doesn't have time to check the forums, much less a thread started back in 2018. I just bought a couple wheels from him via email...he was extremely...
  18. Replies
    17
    Views
    608

    This is another thread you should read: ...

    This is another thread you should read:

    https://driveviper.com/forums/threads/13759-Nth-Triple-Carbon-Clutch-500-mile-follow-up

    It discusses Andy's input shaft issues, and the subsequent "too...
  19. Replies
    17
    Views
    608

    The details matter...if you don't get the input...

    The details matter...if you don't get the input shaft completely deburred properly, you'll end up with engagement issues.

    I did a detailed write-up of the Nth Moto Clutch on my Gen 4, including...
  20. Even my POS Gen 4 gets a lot of attention when I...

    Even my POS Gen 4 gets a lot of attention when I show up at the drag strip. People immediately recognize what it is, and generally have a lot of respect for the platform. Granted, these aren't...
  21. Replies
    24
    Views
    646

    That assumes that the battery tester works as it...

    That assumes that the battery tester works as it is supposed to. In this case, it appears that replacing the battery did help.

    These cars are notorious for large key off battery drain, and that...
  22. Replies
    41
    Views
    1,147

    About the only option that I know of would be to...

    About the only option that I know of would be to swap to some DSS axles, but it's a bit of labor to install them. Not hard, just time consuming.
  23. Thread: crank pulley

    by Steve M
    Replies
    9
    Views
    318

    My Gen 4 with the stock pulley does this...pretty...

    My Gen 4 with the stock pulley does this...pretty sure it is normal, and just a function of how slowly the display reacts to fluctuations.
  24. Replies
    41
    Views
    1,147

    You shouldn't have to...the 2008s like mine were...

    You shouldn't have to...the 2008s like mine were the last of the Vipers that had the weak axles. The 2009-2017 cars all had much stronger versions that should hold up just fine.
  25. Replies
    41
    Views
    1,147

    You need to figure out two things: 1. What...

    You need to figure out two things:

    1. What diameter of wheel you are willing to run
    2. Your estimated trap speed in the 1/4

    18" rears will give you more options with drag radials...you can...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4