Search:

Type: Posts; User: GTS Dean

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    67
    Views
    1,399

    A less obtrusive storage location would be...

    A less obtrusive storage location would be underslung, ahead of the trailer axles.
  2. Replies
    29
    Views
    334

    A small strip of steel gauge metal glued or...

    A small strip of steel gauge metal glued or screwed to the aluminum bracket will allow the use of a magnetic inclinometer.
  3. Replies
    67
    Views
    1,399

    THAT bad boy is going to create chaos on the...

    THAT bad boy is going to create chaos on the roads everywhere it's pulled. It might almost be as serious as my iconic '96 B/W GTS. ;)
  4. It may be a pain to recreate the setup, but an...

    It may be a pain to recreate the setup, but an "after" sequence would be nice to see and appreciated by many. Any rubber bushed suspension is going to have some relative movement. The issue is 'how...
  5. Replies
    37
    Views
    1,224

    Shop for different pads.

    Shop for different pads.
  6. That's what was happening with mine. They just...

    That's what was happening with mine. They just did a normal rebuild with a couple of cones, synchros, blocker rings, sliders, plus a reverse gear that had ground synchro points on it.
  7. Replies
    9
    Views
    154

    It's possible to have every corner be just a...

    It's possible to have every corner be just a little different. Once you have the corner offset figured out, then it becomes easier to get the desired adjustment dialed in quicker.
  8. Replies
    9
    Views
    154

    Assuming your camber is about right, you need to...

    Assuming your camber is about right, you need to push the LBJ forward by going about 2-3 letters higher at the rear pivot and an approximately equal number of steps lower at the front of each...
  9. Sticky: Agreed. The National Viper Clubs have...

    Agreed.



    The National Viper Clubs have never been able to pull off an annual "national" gathering without substantial underwriting of costs by the Dodge Division. I've been watching this for...
  10. Replies
    28
    Views
    1,429

    Not exactly, but very good spot!

    Not exactly, but very good spot!
  11. Replies
    37
    Views
    1,224

    ^Truth.^ It's a hard nut to crack and under a...

    ^Truth.^

    It's a hard nut to crack and under a good bit of preload, but the spring is short and won't spit out like a jack-in-the-box. Lay a rag on the frame underneath the nut because there will...
  12. Thread: Brake Flush

    by GTS Dean
    Replies
    2
    Views
    40

    2 pints is more than plenty.

    2 pints is more than plenty.
  13. Replies
    10
    Views
    338

    Contact Old School.

    Contact Old School.
  14. Replies
    29
    Views
    334

    Your bump steer kits are fantastic for the...

    Your bump steer kits are fantastic for the serious track hounds and there is no debating the quality provided.

    Even for a pretty serious enthusiast like me with a dual-purpose street/time trial...
  15. Replies
    29
    Views
    334

    What are your rear settings? Assuming you did...

    What are your rear settings? Assuming you did bushings F/R, I would be sure to center the wishbone cams in their slots at each corner, check and set camber, then toe.

    Your front camber and toe are...
  16. Replies
    29
    Views
    334

    Good job! Hopefully, it will have the PEP module...

    Good job! Hopefully, it will have the PEP module on the back.
  17. Replies
    29
    Views
    334

    Are you still on stock bushings? Improper bushing...

    Are you still on stock bushings? Improper bushing preload can cause some significant dartiness.
  18. Sirianni Auto Services is down near Churchill HS...

    Sirianni Auto Services is down near Churchill HS on West Ave.
    David Colbath Transmissions on Nakoma by the airport.

    Both have been around for over 40 years.
  19. What part of town do you live in?

    What part of town do you live in?
  20. Replies
    29
    Views
    334

    This guy:...

    This guy:
    https://driveviper.com/forums/threads/24279-Prepping-my-GTS-for-the-Track?highlight=prepping+track

    Gen 1's are +6.0/-6.0. Gauges are simple gravity style and have magnets to stick to...
  21. Replies
    29
    Views
    334

    Here are the final results:

    Here are the final results:
  22. Replies
    29
    Views
    334

    Rear Caster Angle measuring and adjusting

    If there is one recurring theme here when it comes to properly measuring and setting the rear suspension - it's CASTER ANGLE. Whether it's front or rear, the Viper's is individually adjustable and I...
  23. Replies
    8
    Views
    191

    All you should have to do is pull a front and...

    All you should have to do is pull a front and rear rim and show them the Chrysler markings and P/N that are usually found near the hub or on the spokes of the wheels. You will be looking for markings...
  24. Sticky: Read the thread more closely about dues receipts...

    Read the thread more closely about dues receipts and cash vs accrual accounting.
  25. Replies
    37
    Views
    1,224

    I've been tracking my Gen 2 for 25 years. 22 of...

    I've been tracking my Gen 2 for 25 years. 22 of those have been on stock front/40mm rear calipers with 13" discs and no proportioning valve spring. I have run a number of different pad combinations....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4