Search:

Type: Posts; User: GTS Dean

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    4
    Views
    39

    After 25 years of stock shifter and bushing with...

    After 25 years of stock shifter and bushing with many many track miles, I put a bronze cup and Ipsco shifter in mine. I have no complaints about them except the stiff gate spring going to 5th....
  2. The Gen 2 bra will fit. The hood piece as...

    The Gen 2 bra will fit. The hood piece as mentioned above has the NACA clearance cut. The Gen 1 parts were uniformly wider between the headlights. They had 2 triangular plastic insert pockets sewn...
  3. That's a beautiful track - 1/2 mile longer than...

    That's a beautiful track - 1/2 mile longer than Road America. Someone spent some money on rock excavation on the front side of the course. Thanks for sharing!
  4. Replies
    47
    Views
    1,757

    Back in the early 90's, Dodge had a pair of...

    Back in the early 90's, Dodge had a pair of RT/10s running down in Corpus Christi that were reportedly limited to about 3500rpm. They were regularly driven on the beach and splashed. The Intracoastal...
  5. Replies
    47
    Views
    1,757

    ...

    ...
  6. Replies
    47
    Views
    1,757

    You can't use magnaflux on aluminum. ...

    You can't use magnaflux on aluminum.



    Fortunately, the front lowers are interchangeable L/R. The only difference is the steel lower shock adapter brackets, which are bolt-ons.
  7. Replies
    10
    Views
    175

    Serious warning on fuel line "upgrades": A...

    Serious warning on fuel line "upgrades":

    A friend's TT Viper burned and was totaled because the "upgraded" stainless fuel line inner tubes were not compatible with with 10% ethanol from every pump...
  8. Replies
    11
    Views
    233

    Click on 2812 model for adjustment guide:...

    Click on 2812 model for adjustment guide: https://www.koni-na.com/en-US/NorthAmerica/Technology/Adjustment-Guides/
  9. The front calipers have bleed screws on BOTH...

    The front calipers have bleed screws on BOTH halves of the caliper - outboard AND inboard. A bleed/flush is not complete without removal of the wheels.
  10. Replies
    11
    Views
    233

    Early ACRs had Koni 2812's and they were very...

    Early ACRs had Koni 2812's and they were very good shocks. Later ones had Dynamic shocks that were heavily oversprung and prone to seal failure. It could be that your shocks are simply adjusted full...
  11. Sticky: I've been president of my local Rotary Club, both...

    I've been president of my local Rotary Club, both of my Texas construction trade associations and division chair of my national trade association. Not one of these non-profit groups allows the...
  12. Sticky: Thanks for the clarification Matt. Standing by...

    Thanks for the clarification Matt. Standing by...
  13. Sticky: So barely over 1/3 of the regional reps - far...

    So barely over 1/3 of the regional reps - far from even a simple majority - are attempting to officially set the policies of VOA?
  14. Randomly mismatched pad compounds. You shouldn't...

    Randomly mismatched pad compounds. You shouldn't push the car very hard with them because you'll have different coefficients of friction front/rear. I do that purposely with plenty of objective...
  15. Replies
    19
    Views
    162

    I see what you did there...

    I see what you did there...
  16. Replies
    67
    Views
    1,477

    A less obtrusive storage location would be...

    A less obtrusive storage location would be underslung, ahead of the trailer axles.
  17. Replies
    29
    Views
    364

    A small strip of steel gauge metal glued or...

    A small strip of steel gauge metal glued or screwed to the aluminum bracket will allow the use of a magnetic inclinometer.
  18. Replies
    67
    Views
    1,477

    THAT bad boy is going to create chaos on the...

    THAT bad boy is going to create chaos on the roads everywhere it's pulled. It might almost be as serious as my iconic '96 B/W GTS. ;)
  19. It may be a pain to recreate the setup, but an...

    It may be a pain to recreate the setup, but an "after" sequence would be nice to see and appreciated by many. Any rubber bushed suspension is going to have some relative movement. The issue is 'how...
  20. Replies
    38
    Views
    1,342

    Shop for different pads.

    Shop for different pads.
  21. That's what was happening with mine. They just...

    That's what was happening with mine. They just did a normal rebuild with a couple of cones, synchros, blocker rings, sliders, plus a reverse gear that had ground synchro points on it.
  22. Replies
    9
    Views
    168

    It's possible to have every corner be just a...

    It's possible to have every corner be just a little different. Once you have the corner offset figured out, then it becomes easier to get the desired adjustment dialed in quicker.
  23. Replies
    9
    Views
    168

    Assuming your camber is about right, you need to...

    Assuming your camber is about right, you need to push the LBJ forward by going about 2-3 letters higher at the rear pivot and an approximately equal number of steps lower at the front of each...
  24. Sticky: Agreed. The National Viper Clubs have...

    Agreed.



    The National Viper Clubs have never been able to pull off an annual "national" gathering without substantial underwriting of costs by the Dodge Division. I've been watching this for...
  25. Replies
    47
    Views
    1,757

    Not exactly, but very good spot!

    Not exactly, but very good spot!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4